ADJUST LYMAN TANG SIGHT

Talk about things other than the Model 8's and 81's
Post Reply
oldsetter
Posts: 13
Joined: Fri Mar 06, 2020 11:06 am

ADJUST LYMAN TANG SIGHT

Post by oldsetter »

Hi All
This may be a ROOKIE question but.......I just acquired a Lyman AT peep sight but cant seem to adjust it to be effective.
I don't want to force an adjustment but nothing seems tto move to get the stalk high enough to look over the "hump"
ANYTHING is welcome I feel so damn dumb!
An armed society is a polite society. Manners are good when one may have to back up his acts with his life.
Robert A. Heinlein
User avatar
1913Model8
Posts: 177
Joined: Wed Jun 09, 2021 3:36 pm
Location: Minnesota
Contact:

Re: ADJUST LYMAN TANG SIGHT

Post by 1913Model8 »

Curious to see what people have to say on this. One day I plan to acquire one of these, so if I run into the issue I shall now know myself :lol: I love the quote you have also attached.
TJ
Owner of the Model 8 Service Tool
Model-8-service-tool.sqaure.site
oldsetter
Posts: 13
Joined: Fri Mar 06, 2020 11:06 am

Re: ADJUST LYMAN TANG SIGHT

Post by oldsetter »

:D :) ;)
Thanks again for the "Fabulous " Model 8 tool
Hope someone will send a key to this sucker I waited till I found one that LOOKED like new but the tariff was HIGH..
Hope I didn't wait so long to get a turkey :mrgreen:
An armed society is a polite society. Manners are good when one may have to back up his acts with his life.
Robert A. Heinlein
User avatar
Roger
Posts: 818
Joined: Tue Jan 17, 2012 6:41 pm
Location: Iowa

Re: ADJUST LYMAN TANG SIGHT

Post by Roger »

Sir, I have many Marbles and Lyman peep sights for M8and M81s. I’m not sure what you are asking,but I’ve never had any that wouldn’t adjust high enough. On the Lyman, usually there isn’t a height lock like the Marbles has. Turn the knurled section on the stem either way to go up or down. If it’s locked in place you may have to soak it with something like PB Blaster to break it loose. Even in brand new condition ,it should turn relatively easily. Although I’ve had some that were somewhat stubborn until oil was applied.Thats about all that I can tell you.
Roger
Roger
raw4555@gmail.com
oldsetter
Posts: 13
Joined: Fri Mar 06, 2020 11:06 am

Re: ADJUST LYMAN TANG SIGHT

Post by oldsetter »

Many thanks I was afraid to apply too much force to try and turn the knurled stem part in fear that I was forcing something which was not intended to move.
Ive had it soaking overnight in Balistol so I will give a try to turn it.
Thanks again! :o
An armed society is a polite society. Manners are good when one may have to back up his acts with his life.
Robert A. Heinlein
User avatar
Hibby83
Posts: 599
Joined: Mon Feb 18, 2019 7:35 am

Re: ADJUST LYMAN TANG SIGHT

Post by Hibby83 »

OldSetter.

I would suggest an immersion bath overnight/couple days in oil/diesel/kerosene or dealer's choice to help soak in, even a few treatments between wiith heat from a hair dryer won't hurt.

The sight appear to be factory true "not modified or fooled with?"
oldsetter
Posts: 13
Joined: Fri Mar 06, 2020 11:06 am

Re: ADJUST LYMAN TANG SIGHT

Post by oldsetter »

Appears new (no box) but the blue is new looking and it is marked in very small letters AT under the base and an almost too small to see lyman under the knurled section on the base.
It appears new and I sure paid for it its new looking looking appearance. :shock: :mrgreen:
An armed society is a polite society. Manners are good when one may have to back up his acts with his life.
Robert A. Heinlein
Post Reply